Tag Archives: Pfriem Pils

Pfriem Pilsner 2024

Posted on by

I have done a version of this three times previously, usually with some minor variations for hops or yeast. This time, I decided to do the hop varieties and timings exactly as written (with adjustments for alpha acid), to follow the original Pfriem Pilsner clone recipe from Dave Carpenter’s Lager book. Without further ado, here’s what I did.

Pfriem Pilsner 2024

  • 9.75 lb. pilsner malt (Rahr)
  • 6 oz. Carafoam malt (Weyermann)
  • 0.5 tsp. BrewTanB, in mash
  • 0.75 oz. Perle hop pellets (6.3% alpha), 60 minute boil
  • 0.5 oz. Tettnang hop pellets (2.4% alpha), 60 minute boil
  • 0.5 oz. Tettnang hop pellets (2.4% alpha), 10 minute boil
  • 0.75 oz. Saphir hop pellets (2.3% alpha), 10 minute boil
  • 0.5 oz. Spalt Spalter hop pellets (4.3% alpha), 10 minute boil
  • 0.5 tsp. BrewTanB, 10 minute boil
  • 1 Whirlfloc tablet, 5 minute boil
  • 1.5 oz. Tettnang hop pellets (2.4% alpha), 10 minute whirlpool
  • 0.75 oz. Saphir hop pellets (2.3% alpha), 10 minute whirlpool
  • 0.5 oz. Spalt Spalter hop pellets (4.3% alpha), 10 minute whirlpool
  • 2 pkg. Diamond dry lager yeast (Lallemand)

Target Parameters

  • 1.046 s.g., 1.007 f.g., 5.1% abv, 4 SRM, 38 IBU
  • Full volume step mash, with 45 minutes at 142°, 45 minutes at 156°, and 10 minutes at 168°; 70 minute boil
  • Water built up from RO, to hit target parameters of 62 ppm Ca, 11 ppm Mg, 121 ppm SO4, and 51 ppm Cl, with RA=-50 ppm

Procedure

  • I built up my mash water from 7.5 gallons of RO water, with 3 g calcium chloride, 3 g epsom salt, and 4 g gypsum. Then, I heated it to 146° before adding the grains and holding at 142° for 45 minutes, with recirculation. Then, I raised the mash to 156° for 45 minutes and finished up at 168° for 10 minutes.
  • After the mash, I pulled the grains. I collected 6.8 gallons of runnings with a gravity of 1.041, for 74% mash efficiency.
  • I brought the runnings to a boil, boiling for 10 minutes before adding the first round of hops and proceeding with the rest of the recipe as written. In total, this was a 70 minute boil.
  • At the end of the boil, I turned off the heat, added the whirlpool hops, and whirlpooled for 10 minutes before continuing with the rest of the chill.
  • Once the beer was down to 72°, I transferred to the fermenter and chilled down to 46° in my fermentation chamber, before pitching the yeast.
  • I brewed this beer on 28 October 2024, and the starting gravity was 1.049.
  • The starting fermentation temperature was 48°, and I held it here until 3 November 2024, when I raised the temperature to 52°. On 17 November, I raised the temperature to 54°, and then to ambient (~62°) on 24 November 2024.
  • I kegged the beer on 25 November 2024. Final gravity was 1.009, for 5.3% abv.

Tasting

  • Appearance
    • Clear, but short of brilliant; there is just a tiny touch of barely visible haze. It is a straw-colored beer that pours with a fine and persistent white head, which leaves some nice lacing on the glass.
  • Aroma
    • Light notes of cracker and honey in the malt, and a pleasant light floral hop aroma, with a touch of fresh hay. This beer smells awesome!
  • Flavor
    • Medium-high bitterness, grainy sweet malt character; hop flavor is lightly herbal. Minerally feel to finish out the flavor.
  • Mouthfeel
    • Medium carbonation, medium light body, dry finish. Minerally, but not unpleasantly so.
  • Would I Brew This Again?
    • I am feeling pretty good about this recipe overall. It is perhaps a touch more bitter than I prefer in all of my pils, but I like the hop aroma and malt character; the overall aroma is amazing! I wouldn’t mind a touch taller head (but that may be in the pour), and I also must ding the beer a bit for its clarity. I wonder if the persistent light haze is from the large dose of whirlpool hops? I could have used some finings, and might do that next time for a pilsner-type beer, because clarity is something important to me for these.
  • Overall
    • 8/10

Pfriem Pils 2023

Posted on by

German pils is perhaps my favorite style. It’s surprisingly complex, highlights both malt and hops in a non-IPA sort of way, and is a fun challenge to do well. At current count, I’ve made 16 batches over the past 7 years.

My latest batch retreads the Pfriem Pils recipe from Dave Carpenter’s Lagers book. I’ve made versions of this twice previously, and it’s a really solid beer. Every iteration has some changes in hops, grist, and yeast, and this version is no different. I leaned into the HOPBOX European hops I had on hand, ending up with a nice combo of Hallertauer Mittelfrueh, Saaz, and Tettnang. Although the original recipe calls for acidulated malt, I worked with lactic acid instead, which provides pretty much the same effect. Lallemand’s Diamond Lager yeast rounded out the recipe–this strain is (in my opinion) one of the best dry lager yeasts out there right now. It ferments quickly and cleanly, and drops clear with minimal fuss.

Pfriem Pils 2023

  • 9.5 lb. Viking Pilsner Zero malt
  • 0.5 lb. Carafoam
  • 0.5 tsp. BrewTanB (added to mash)
  • 1.5 oz. Hallertauer Mittelfrueh hop pellets (5.2% alpha), 60 minute boil
  • 0.5 tsp. BrewTanB, 10 minute boil
  • 1 Whirlfloc tablet, 5 minute boil
  • 1 oz. Saaz hop pellets (2.4% alpha), 5 minute boil
  • 0.5 oz. Tettnang hop pellets (2.2% alpha), 5 minute boil
  • 1 oz. Saaz hop pellets (2.4% alpha), 10 minute whirlpool
  • 1.5 oz. Tettnang hop pellets (2.2% alpha), 10 minute whirlpool
  • 2 pkg. Diamond Lager dry yeast (Lallemand)

Target Parameters

  • 1.046 s.g., 1.007 f.g., 5.1% abv, 4 SRM, 36 IBU
  • Full volume step mash, with 45 minutes at 144°, 30 minutes at 156°, and 10 minutes at 168°; 60 minute boil
  • Water built up from RO, to hit target parameters of 59 ppm Ca, 8 ppm Mg, 89 ppm SO4, and 63 ppm Cl, with RA=-47 ppm

Procedure

  • To 7.5 gallons of RO water, I added 2.9 g gypsum, 2.4 g epsom salt, and 3.7 g of calcium chloride, in order to hit my target parameters.
  • I heated the strike water to 146°, and added the grains and BrewTanB. I set the mash for 144° with recirculation, holding it here for 45 minutes. Then, I raised the mash to 156° for 30 minutes, and finally mashed out at 168° for 10 minutes.
  • After removing the grains, I had 6.6 gallons of runnings with a gravity of 1.037, for 66% mash efficiency.
  • I brought the kettle to a boil, boiling for 60 minutes and adding the hops and finings per the recipe. Finally, I turned off the heat and chilled down to 82°. I let things settle, transferred to the fermenter, and let it chill to 50° before pitching the yeast.
  • Starting gravity was 1.044. I brewed this beer on 12 August 2023.
  • The beer was held at 52° for the bulk of fermentation, and raised to 60° on 19 August. I crashed it to 34° on 27 August 2023.
  • I kegged the beer on 7 September 2023, using a closed transfer. It tastes amazing at this point, with notes of hay in the aroma. In terms of appearance, it’s still reasonably hazy. Final gravity was 1.012, for 4.2% abv. It’s a true session beer!

Tasting

  • Appearance
    • Very clear, nearly brilliant; a light yellow beer with a persistent and creamy white head.
  • Aroma
    • Lightly spicy (like a spice cake); malt aroma is slightly sweet.
  • Flavor
    • Medium-high bitterness with a lingering finish; slightly herbal quality to the hop profile. The beer has a crackery malt flavor, with a bit of sweetness also. The balance is tilted towards the bitter side.
  • Mouthfeel
    • Smooth, moderate body, with medium-low carbonation (especially when “slow-poured”). Moderately dry and very crisp finish.
  • Would I Brew This Again?
    • Yes! It’s a great recipe. I might like to try it with more floral-type hops, such as the Edelweiss blend, for something different. I perfected a slow-pour on my faucet, to approximate the creamy and highly persistent heads you can get with the “side-pour” taps. Now that I’ve figured this out, I’m happy with the beer on home draft.
  • Overall
    • 10/10

Black Bear Pils

Posted on by

I really like German pils, and make it pretty frequently…with 14 brews of this style under my belt, it’s time for number 15! For this iteraton, I returned to Dave Carpenter’s Lager book for inspiration via the Pfriem Pilsner recipe. My current version is modified for hop varieties on-hand; thanks to my HOPBOX I had a few different German hops in the freezer, which were a perfect match for this style. Notably, I’ve never brewed with Saphir before, and wanted to give it a try. I also had some S-189 in my stockpile (from a freebie give-away), and figured this would be a good batch to try it in.

The batch practically named itself. I was brewing in my garage on a hot summer day, with the Foundry right at the garage door entry. I ran across the driveway (our house is horseshoe shaped, with a parking space right in the middle of the U) to grab something from my fermenting area, leaving my brew rig unattended for a minute. Looking out the window and towards the garage, I suddenly noted a black bear wander into our yard. It ambled over to the open garage door, obviously intrigued by the malty aromas of a pilsner mash. As it started to poke its nose around the Foundry, two thoughts went through my head…first, “That’s so cool! I should get a picture!” The second thought was…”My beer! The bear! I don’t want the mash tun tipped over! The bear could get burned! My beer could get wasted! Action! Quick!” In an instant, I was at the door, yelling at the unexpected visitor to get out of my garage! With what I can only assume was surprise, the bear craned its neck to look at me, and then booked it out of the yard. Disaster averted! And beer recipe named.

Black Bear Pils

  • 10.25 lb. Barke pilsner malt (Weyermann)
  • 2 oz. acidulated malt (Weyermann)
  • 1 oz. Hallertau Tradition hop pellets (6.1% alpha), 60 minute boil
  • 0.5 oz. Hallertau Tradition hop pellets (6.1% alpha), 10 minute boil
  • 0.5 oz. Saphir hop pellets (3.7% alpha), 10 minute boil
  • 0.5 oz. Spalt Spalter hop pellets (3.0% alpha), 10 minute boil
  • 1 tsp. BruTanB, 10 minute boil
  • 1 Whirlfloc tablet, 5 minute boil
  • 1.5 oz. Saphir hop pellets (3.7% alpha), 10 minute whirlpool
  • 2 pkg. SafLager German lager yeast (Fermentis S-189)

Target Parameters

  • 1.047 s.g., 1.007 f.g., 35 IBU, 4 SRM, 5.2% abv
  • Full-volume mash, no sparge, at 142° for 40 minutes and 156° for 40 minutes, with 10 minute mash-out at 168°
  • Claremont tap water adjusted with RO and minerals to hit 47 ppm Ca, 2.5 ppm Mg, 33 ppm Na, 92 ppm SO4, 39 ppm Cl, and 11 ppm HCO3, with 9 ppm alkalinity and RA=-26 ppm

Procedure

  • To produce the water, I added 2 mL of 88% lactic acid to to 2.5 gallons of tap water to remove the bicarbonate, and then 1/4 of a Campden tablet to remove the chloramines. Then, I added 4.5 gallons of RO water and 3.5 g gypsum to achieve a final water with 47 ppm Ca, 2.5 ppm Mg, 33 ppm Na, 92 ppm SO4, 39 ppm Cl, and 11 ppm HCO3, with 9 ppm alkalinity and RA=-26 ppm.
  • I heated the mash water to 146°, and added the grains to hit a target mash temperature of 142°. I held it at this temperature for 40 minutes, chasing away bears when necessary. It wasn’t necessary to add lactic acid for this batch, because I already had acidulated malt. After the initial rest, I raised the mash temperature to 156°, and held it here for another 40 minutes. Finally, I heated to 168° and held it there for 10 minutes before removing the grains.
  • In total, I collected 6.5 gallons of runnings with a gravity of 1.041, for 70% mash efficiency.
  • I brought the runnings to a boil, adding hops, BrewTanB, and Whirlfloc as indicated in the recipe. In total, I had a 70 minute boil.
  • I brewed this beer on 20 August 2022. After chilling to ~75°, I transferred the beer to my fermenter and continued to chill overnight down to 48°.
  • Starting gravity was 1.047, right on target. I pitched the yeast on 21 August 2022, and started the fermentation at 48°.
  • I raised the fermentation temperature to 55° on 28 August, and then to 60° on 1 September 2022. I crashed the fermenter to 36° on 3 September 2022, and lagered at this temperature until kegging on 28 October 2022.
  • Final gravity was 1.010, for 4.9% abv. Although there was some yeast disturbance upon kegging and initial serving, I was pulling remarkably clear drafts within about 10 days. I’m quite pleased with that!

Tasting

  • Appearance
    • Near brilliantly clear, straw-colored beer, which pours with a medium white head of modest persistence.
  • Aroma
    • Spicy hop aroma with a doughy and very slight honey quality to the malt. Clean fermentation profile in the aroma. Wonderful!
  • Flavor
    • Cracker-like malt profile, with a slight bit of malty sweetness. Moderately high and clean bitterness, with a modest spicy quality. Clean yeast character. The malt is at the front of the taste, and the bitterness sneaks in and then pops for an extended and prominent bitter finish. The mineral character of the water also comes through, against the hops.
  • Mouthfeel
    • Medium-light body, moderate carbonation, off-dry finish.
  • Would I Brew This Again?
    • This is a super solid German pils! I wish the head retention was better, but everything else works super well. I’m also pleased with the yeast–it emphasizes the malt well, and also dropped clear pretty quickly.
  • Overall
    • 9/10

Pfriem Pilsner

Posted on by

I recently bought a Foundry brewing system, and chose a German pils as my first brew. First off, I really like this style. Importantly for a first spin on the Foundry, it gave me a chance to try out a step mash. The recipe is from Dave Carpenter’s Lager book, modified slightly for hop varieties. Otherwise, it’s pretty much as advertised.

Pfriem Pilsner

  • 9.5 lb. Pilsner malt (Weyermann)
  • 7 oz. Carafoam malt (Weyermann)
  • 3 oz. acidulated malt (Weyermann)
  • 0.6 oz. Perle hop pellets (7.1% alpha), 60 minute boil
  • 1 oz. Crystal hop pellets (4.5% alpha), 10 minute boil
  • 0.5 oz. Spalt Spalter hop pellets (3.0% alpha), 10 minute boil
  • 0.5 oz. Vanguard hop pellets (6.5% alpha), 10 minute boil
  • 1 oz. Crystal hop pellets (4.5% alpha), 10 minute whirlpool
  • 0.5 oz. Spalt Spalter hop pellets (3.0% alpha), 10 minute whirlpool
  • 0.5 oz. Vanguard hop pellets (6.5% alpha), 10 minute whirlpool
  • 2 pkg. Saflager Lager Yeast (W34/070)

Target Parameters

  • 1.046 s.g., 1.006 f.g., 5.2% abv, 3 SRM, 35 IBU, 5.25 gallon batch
  • Full volume step mash, with 40 minutes at 142°, 40 minutes at 156°, and 10 minutes at 168°; 70 minute boil
  • Claremont water with carbonates knocked out via lactic acid and Campden tablet to remove chloramines.

Procedure

  • While the 7.25 gallons of water were heating, I added 6 mL of 88% lactic acid to neutralize the carbonate load, in addition to adding a Campden tablet. No other minerals were added.
  • It took 29 minutes to heat up from tap water temperature (~115°) to 146° for the mash-in temperature. I also added 5 mL of 88% lactic acid (but realized I had the wrong settings, and this was probably too much). I hit an initial mash temperature of 142°, and held it there for 40 minutes. 10 minutes into the mash, I started recirculating. Then, I raised the temperature to 158°, which took around 20 minutes (I started at 75% power, and then upped it to 100% power for the last 10 minutes). To raise to 168° for mash-out, it took ~7 minutes at 100% power. To get boiling temperatures, it took around 50 minutes. I noted that it was boiling (bubbling) before the panel actually showed 212° (~207°).
  • The post-mash volume was 6.4 gallons, with a gravity of 1.043, for 72% mash efficiency.
  • I boiled for 70 minutes, adding hops and finings per the recipe.
  • After the boil, I chilled and transferred to the fermenter. In the fermenter, I continued the chill, down to 52°. Then, I pitched the yeast.
  • I brewed this beer on 17 October 2020, and it had a starting gravity of 1.049.
  • I raised the beer to 60° on 30 October 2020.
  • I lowered the beer to 55° on 1 November 2020, and down to 33° on 6 November 2020.
  • I kegged using semi-closed transfer on 30 November 2020.
  • Final gravity was 1.013, for 4.7% abv.

Tasting

  • Appearance
    • The beer pours with a persistent, thick, and white head–absolutely gorgeous! This is a true slow-pour beer. I am so pleased with the heading I’ve been getting from my pilsners. In the glass, the beer has a light gold color, with a very slight haze.
  • Aroma
    • Light grainy malt note, with a low level of spicy hop character. Very clean yeast character.
  • Flavor
    • Moderately low grainy-sweet malt character. The hops are more prominent, with a slight herbal character and clean bitterness that is pretty strong, almost approaching a level of harshness. Yeast flavor is very clean.
  • Mouthfeel
    • Moderate/moderate-low level of carbonation, due to the high head on the pour that drives off some of the CO2. The finish is off-dry, with a light and crisp body.
  • Would I brew this again?
    • Yes? I really need to take a look at my hopping levels, and perhaps consider going with American hops rather than European ones to get a better aroma. The persistent haze is annoying, but I also misjudged the lactic acid addition, which I suspect might be a factor, as well as the whirlpool. I’ll dial back the hops in my next batch and avoid the whirlpool, because this is more bitter than I really like for a pils. Once I’m buying RO water again, I’ll definitely be building up my water profile, rather than augmenting the rather over-mineralized tap water. So, there are things I like about the recipe, but I think I can continue to adjust for improvements.
  • Overall
    • 6/10