Raspberry Belgian 1.1

In another brew for the Lake Arrowhead Event, I’m doing a second attempt at my Raspberry Belgian. The first version turned out reasonably well, although I felt like it needed a bit more tartness as well as a bit more body. I thought the body could be augmented by doing a batch sparge instead of a no-sparge technique; the latter consistently leads to low efficiency on my system and thus a lower starting gravity. As for the tartness…I elected to do a kettle sour instead of improvising with acid malt.

Recently, one of my fellow homebrew club members presented on kettle souring, particularly his approach with using a yogurt-based culture. Now, I’ve done kettle souring once before–with incredible results–but in that case I used a commercial lacto strain specifically for homebrewers. I was intrigued by the thought of souring more cheaply, and thought this was a great batch in which to give it a try.

sour_culture

Sour culture ingredients and tools

For my culture, I chose The Greek Gods’ brand nonfat Greek yogurt–other homebrewers have reported success with it, and it has a nice blend of various lacto strains. So, 24 hours before my planned brew session, I made a 1L starter (1 L water, 100 g extra light DME, and a pinch of Fermax yeast nutrient) with 3 tsp. of yogurt. Because I’m not using a stir plate, next time I’ll want to break up the yogurt a bit; I noted that the first clump I put in never really broke up well, even with some gentle swirling. Greek yogurt is thick! I let the starter sit overnight on a heating pad set for 100° (I taped the sensor on the side of the flask). By the next day, it had a nice sour aroma, so I deemed it ready to go.

Raspberry Belgian 1.1

  • 5 lbs. Château Pilsen malt (Castle Malting)
  • 2 lbs. white wheat malt (Great Western Malting)
  • 0.5 lb. carapils (Briess)
  • 0.5 lb. flaked oats (store brand quick oats)
  • 0.5 lb. flaked wheat
  • 0.20 oz. Warrior hop pellets (15.8%), 60 minute boil
  • 0.15 oz. Willamette hop pellets (4.9%), 15 minute boil
  • 1 Whirlfloc tablet, 10 minute boil
  • 0.5 tsp. Fermax, 10 minute boil (added before souring)
  • 1 tsp. Fermax, 10 minute boil (added after souring)
  • 1 pkg. Belgian Wit Ale yeast (WLP400), prepared in 1L starter
  • 4.25 cups (1 L) raspberry puree (Vintner’s Harvest brand)

Target Parameters

  • 156° mash, 60 minutes
  • 10 minute boil and 24 hour kettle sour prior to 60 minute boil
  • 1.044 o.g., 1.012 f.g., 4.2% abv, 14 IBU, 3 SRM, 5 gallons into the fermenter

Procedure

  • I prepared the sour culture as specified above, 24 hours in advance.
  • On brew day (part I), I mashed in with 3 gallons of water at 166.5°, to hit my mash target temperature of 156° right on the nose!
  • I added 1.6 gallons of water to sparge, vorlaufed, collected first runnings, and then added 3.5 gallons of water for the second sparge.
  • In total, I collected 6.75 gallons of wort at a gravity of 1.038–81% efficiency!
  • Using 3.5 tsp. of 88% lactic acid, I adjusted the pH of the wort to around 4.2. This was a slight overshoot of my target, but I figured I would be OK.
  • I boiled the wort for 10 minutes, adding the first bit of Fermax. After 10 minutes, I chilled the wort to ~100° and then added the yogurt culture. I left the kettle on a heating pad, with the temperature controller set to 100°.
  • After ~21 hours, the temperature had settled to around 94°, and the pH was down to ~3.1 (a bit too sour for my tastes!). I added 1.5 tsp. of chalk to the kettle to raise things up a bit.
  • I boiled the wort for 60 minutes, adding the various ingredients per the schedule in the recipe. At the end, I chilled the wort down to 80° and then transferred it into my fermenter. Six gallons of wort made it in. I then did the remaining chill to 66° in my fermentation chamber. I pitched the yeast, and let things move along.
  • The final pH prior to the yeast pitching was 3.39; much more reasonable. It may even be a bit too tart yet, but we’ll see. Starting gravity was 1.044, right where I wanted it to be!
  • I brewed the beer and pitched the yeast on 27 June 2017. Initial fermentation was at 66°. After 4 days, on 1 July 2017, I added 4.25 cups of raspberry puree and raising the temperature to 68°.
This entry was posted in Belgian sour, fruit beer, sour, sour beer and tagged , , , , , . Bookmark the permalink.

2 Responses to Raspberry Belgian 1.1

  1. Pingback: A good use for extra fruit puree | Andy's Brewing Blog

  2. Pingback: Kegging Updates: Raspberry Belgian, Thumbspike Saison 2.1 | Andy's Brewing Blog

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s